BLA

One end snaps around a tube and the other end inserts into a tube. Moulded in black nylon.

The BLA high performance foils are designed to provide additional lift plus increased speed and control on most outboard powered boats. These tough high strength foils provide both quicker on-plane and higher top end speeds while helping to prevent porpoising and sideways slip.

Hydrofoil to suit O/B over 25HPThe new high performance foils are designed to provide additional lift plus increased speed and control on most outboard powered boats.These tough high strength foils provide both lower on-plane and higher top end speeds while helping to prevent porpoising and sideways slip.Features:Increased lift with improved take off and stabilityHelps eliminate cavitation and porpoisingForces stern up and bow down for smoother take offsTwo piece design allows for easy installationComplete with stainless steel mounting hardware.

The high performance SE Sport foils will provide more speed and precision control on most outboard and stern drive powered boats. Made of flexible, high strength co-polymer, the foils are rugged enough to stop porpoising and side-to-side movement. Specially engineered crescent shaped planing surface funnels water flow to add thrust, cut planing time and provides both slower 'on plane' and higher 'top end' speeds. A special tracking feature, TURBO TRAC, locks in high speed turns without cavitation (prop blowout) for precise control. SE 200 suits motors from 8HP up to 40HP, while the SE 300 suits motors from 40HP to 350HP and are supplied with 6mm x 32mm stainless steel mount bolts, lock nuts and insulators.FeaturesIncreased lift with crescent plane surfaceSmall footprint 75-100mm narrower than most other foilsTURBO TRAC enhances thrust and controlControl tip cuts tight turnsSleek shape compliments today's boat designsOne piece high strength engineering grade co-polymerMounting holes suit other popular one piece foils

Replacement cap with gauge to suit 200110 deluxe fuel tank.

The Voltage Sensitive Relay (VSR) allows two batteries to be charged at the same time. It will automatically prioritise the charging of the start battery in twin battery systems. When the engine is first started the relay is open and remains open until the start battery has reached a preset 13.7 volts for 12 volt systems and 27.4 volts for 24 volt systems. At the rated voltage the relay closes providing charge to both batteries (start and house). When the voltage drops below 12.8 volts (when the engine is stopped), the VSR disengages, separating the batteries.This system eliminates the possibility of draining the start battery and protects electronics powered by the house battery from harmful engine starting spikes. A VSR has no voltage drop as opposed to conventional charge diode isolators. Surface mounted, 5mm roundhead screws.A dual sensing VSR is also available. This model allows the unit to sense the voltage of both batteries

Manufactured from UV stabilised clear polycarbonate. Suitable for new or existing self draining cockpits/floors. PVC mounting seal and solid polypropylene sealing ball. Must be installed on a near vertical flat face.Outside Dia (mm):113 Overall length (mm):74 Cut Out Dia:44 Mount Screws (mm):5 c/s

The IPX6 waterproof 12/24V Qi certified waterproof wireless charging range enables charging for the outdoor environment, without the need for phone charging cables. Designed from the ground up, this is the world’s first waterproof wireless charge system created specifically for use on board, with the unique technology housed in an IPX6, fully encapsulated and sealed unit.

Working directly with 12/24V systems, ROKK Wireless is ideal for life on the move and is perfect for sail and power boats and also RV. Easy install, anywhere you need your phone – indoors or out. No more wires! Exceeding the latest and highest standards of the Qi wireless protocol, ROKK Wireless is independently certified to deliver ultra-safe charging anywhere on board.

Key Features
• The world’s first 12-24V wireless waterproof Qi™ certified charger

Safety
• Foreign object detection system
• Thermal management system
• UV stable

Technical
• IPX6 waterproof sealed unit
• Fast Charge Technology
• High friction non-slip pad
• Qi certified
• Marine grade materials

Install
• 3 installation options
• Easy install
• No sealant required

QI™ Compatibility
Qi™ is a wireless technology that uses inductive charging. The ROKK wireless range has been engineered to be Qi compatible, allowing universal charging for every wireless charging compatible device.

The IPX6 waterproof 12/24V Qi certified waterproof wireless charging range enables charging for the outdoor environment, without the need for phone charging cables. Designed from the ground up, this is the world’s first waterproof wireless charge system created specifically for use on board, with the unique technology housed in an IPX6, fully encapsulated and sealed unit.

Working directly with 12/24V systems, ROKK Wireless is ideal for life on the move and is perfect for sail and power boats and also RV. Easy install, anywhere you need your phone – indoors or out. No more wires! Exceeding the latest and highest standards of the Qi wireless protocol, ROKK Wireless is independently certified to deliver ultra-safe charging anywhere on board.

Key Features
• The world’s first 12-24V wireless waterproof Qi™ certified charger

Safety
• Foreign object detection system
• Thermal management system
• UV stable

Technical
• IPX6 waterproof sealed unit
• Fast Charge Technology
• High friction non-slip pad
• Qi certified
• Marine grade materials

Install
• 3 installation options
• Easy install
• No sealant required

QI™ Compatibility
Qi™ is a wireless technology that uses inductive charging. The ROKK wireless range has been engineered to be Qi compatible, allowing universal charging for every wireless charging compatible device.

The ultimate rapid charge waterproof USB charger with dual socket connectivity that can charge devices up to 3x faster than standard USB sockets. Featuring an ultra low profile, that’s perfect for any outdoor application.

As smartphones and tablets proliferate on board, the need for a charging station to keep them topped up is obvious. And while a charging fixture belowdecks is helpful, what about charging while on deck and the unit is being used in the cockpit? And if it’s going to be in the cockpit, it better be waterproof. The ROKK Charge+ checks all those boxes.

According to Scanstrut, it works with any USB type A connector and you can charge two devices at once. It has a click-and-lock lid and is IPX6 waterproof with the cover closed. It also reportedly charges as much as three times faster than a standard USB socket. The unit has a 316-grade stainless steel hinge and spring and has an anti-snag cover that aligns the cables when the cover is closed.

This is a truly useful and timely product in the days of hand-held devices on board.

Features
• Universal fit for any USB Type-A connector
• Charge up to 2 devices at a time
• Easy Install
• Click & Lock Lid
• Output current 4.2A (total)
• IPX6 waterproof with cover closed
• Up to 3x faster than standard USB sockets
• Waterproof with 1, 2 and even no cables plugged in
• Anti-corrosion coating on circuit board
• UV resistant
• 316 stainless hinge and spring

All Savwinch Drum Winches feature a sealed motor and gearbox with a 316 grade stainless steel drum and body to protect from water ingress and corrosion and come complete with double braid rope, chain and switchgear for hassle free anchoring.

Features
• Motor is fully sealed from corrosion/water. No exposed terminals
• Custom rope kits available to suit any anchoring depth
• Australian designed
• Motor & gearbox can be adjusted in up to 12 positions to drum
• Retailed packaged

The Guide Roller is used to assist the lay of the rope/chain on the drum and avoid damage from chafe.

Designed specifically for hassle free use whilst anchoring in a variety of bottom types, especially were there is heightened risk of snagging regular anchors. Delta style design allows for a strong hold, while the slider allows for easy retrieval if the anchor becomes snagged.

ProSport Generation 3 On-Board Marine Battery Chargers incorporate all-digital microprocessor control. Like no other, the ProSport Series provides automatic installation feedback with its exclusive “System Check OK” and individual “Battery Bank Trouble” LED indicators, and also has the most advanced energy saving mode. After fully charging and conditioning batteries, ProSport’s Energy Saver Mode will monitor and Auto Maintain batteries only when needed to maintain a full state of charge, resulting in maximum reserve power performance and lower AC power consumption and operating costs. Each ProSport model has 2 digitally selectable charge profiles to choose from with a third high performance AGM HP profile on the ProSport20 Dual and includes a once-a-month storage reconditioning mode for extending battery life.

Made from EVA foam, pre-shaped and drilled to suit most Mercury®/Johnson®/Evinrude®/Honda®/Suzuki®/Tohatsu® outboard bracket mounts. These pads reduce noise transfer by 15-40% and help reduce electrolysis. Rated to 250HP. Sold as a pair.

Features
• 60° Beam Angle – A wide-angled, focused beam lights up a large area of the water
• Compact and simple design – Made from a chemically resistant optical polymer with a built in driver, there is a lot packed into this compact light
• Simple to install – Installation needs only a small, 12.5mm hole in the hull to feed the cable through and 4 screws in place. No bonding required
• Easy to clean – Thanks to its Tritonium coating, a simple wipe of the lens removes any underwater growth saving hours of scrubbing each time you use it
• Fish-Strobe Mode – Exceptionally bright, randomised strobing of the light is proven to attract more fish and catch more bait
• Active Thermal Control – ATC prevents overheating. In the event of overheating the ATC system will reduce the LED power level in order to protect the LEDs, or in extreme cases, turn o the fixture completely.
• Colours Control – Colours models are compatible with OceanDMX for full control, interactivity and colour customisation. Alternatively, cycle smoothly between red, green, blue and white with a standard DC switch

Save wear and tear on the outboard pivot bracket and transom mounts with this trailer to outboard motor support. Soft poly ‘V’ holds motor leg and spring tube provides support, yet absorbs impact shocks. Metal yoke at base locks onto trailer rear beam, without requiring a special mount bracket. Support has an adjustable length of 520mm to 780mm. Supplied complete with 300mm rubber strap. Suits up to 150HP motors.

Clean contoured shape to blend with the boats aesthetics. No edges to catch on ropes or crew. Led reliability, energy efficiency and low heat generation. Clear lens for maximum illumination. The red and green colour is created by the LED.

Feature

• High quality, UV stabilised plastic housing
• 12 volt, sold as a pair.
• Dimensions:Base: 93x56mm Depth: 37mm Mount screws: 4mm c/s

Chrome plated brass, flanged base and plug housing with bakelite insulator and brass screw terminals. Plug has a rubber cable entry gland and screw locking mechanism. Plastic screw cap with security chain for when plug is not fitted. Pins are sized to prevent reverse polarity connection.

Stainless steel spring style hatch and window support. When hatch or window is in an open position the spring coil becomes a rigid support. To close, apply side pressure to the middle of the spring coil and the support will collapse to a closed position.

Manufactured from durable white U.V. resistant ASA plastic and featuring a secure closing mechanism. Diamond pattern non-skid surface provides sure-footedness with under lid reinforcing designed to maximise strength and limit flexing. Can be mounted in either the vertical or horizontal plane, with a weather resistant gasket seal. Twin recessed hinges with heavy duty stainless steel pins open to 90°. Complete with Cut Out template and fastening plugs. Intrusion 19mm.

Push button momentary switch. Black neoprene protector. Plastic housing. Suitable for 12/24 volt applications.Dimensions:Panel thickness: 6mmDiameter: 30mmProtrusion: 18mmIntrusion: 22mmMount hole: 22mm